Looking for:
Briggs & Stratton Workshop Manuals - OutdoorKing Repair Forum |
Error: File not found - pdfFiller
Note: Install 1 piston and connecting rod нажмите чтобы узнать больше. Oil piston rings, piston skirt, and compress rings with Ring Compressor StrattnFig. Place piston and ring compressor upside down on bench with projections on compressor facing up. Intdk ring compressor evenly until rings are fully compressed. Then loosen ring compressor very slightly so that compressor can be rotated on piston skirt while holding connecting rod, Fig. Lubricate cylinder bores and crankpin and rotate briggs and stratton intek repair manual pdf until it as at bottom of stroke.
Install 1 piston with ldf towards flywheel anv, Fig. Push piston down by hand until connecting rod is seated on crankpin. Assemble connecting rod cap to rod with match marks aligned, Fig. Torque screws to in. Rotate crankshaft two revolutions to check for binding. Rod should bdiggs be free to move sideways on crankpin.
Repeat for 2 cylinder. Note: The number 1 on 1 connecting rod and the number 2 on 2 connecting rod must be facing PTO ,anual. Lubricate tappets, cam shaft journals and lobes with engine oil. Assemble timing gear to crankshaft. Install tappets. Align timing marks on cam shaft and crankshaft gear and install cam shaft, Fig. Lubricate thrust washer, governor gear and git client download windows cup and assemble to shaft.
Lubricate PTO and cam gear bearing. Install sump with new gasket. Torque screws in sequence shown to in. Check crankshaft end play.
Lubricate oil pump components with engine oil and assemble to sump, Fig. Make sure drive shaft is engaged in camshaft. Install drive shaft. Install inner rotor. Install outer rotor. Install oil pump cover with new O-ring. Torque screws to inyek in. Brigs armatures and ground wire assembly. Note: Push armatures away from crankshaft as far as they will go and temporarily tighten screws. Install air guide. Torque screws to 45 in. Install alternator. Torque screws to 20 in. Assemble oil fill tube to cylinder and crankcase cover, Fig.
Route alternator wires between oil fill tube mounting boss on cylinder and oil fill tube bracket. Route wiring harness between oil fill tube and cylinder. Note: Route armature ground wire under back plate and between starter motor mounting bosses mznual cylinder as shown, Fig.
Install starter motor. Install oil vapor collector and pdv. Install breather. Torque screws to 55 in. Assemble flywheel to crankshaft and страница keyways. Insert flywheel key into crankshaft. Assemble fan and retainer to flywheel, Fig. Install washer and flywheel nut. Assemble flywheel holder, Tool to retainer, Fig. Torque flywheel nut to ft. Rotate flywheel until magnet is under armature laminations. Place thickness gauge. Loosen mounting screw so magnet will pull armature down against thickness gauge.
Torque screws to 25 in. Rotate flywheel to remove thickness gauge. Repeat for second armature. Place briggs and stratton intek repair manual pdf head gasket over alignment dowels on cylinder block.
Install cylinder head nitek, Fig. Torque head bolts in sequence shown to in. Install push rods. Make sure push rods are inserted in recess in tappets. Note: Intake push rods itnek aluminum. Compress valve springs and insert push rods into recess in rocker arm adjustment screws, Fig. Set No. Adjust valves and check, Fig. Torque adjusting screws and jam nuts to briggs and stratton intek repair manual pdf in. Repeat for No. Install valve covers with new gaskets, Fig.
Install No. Assemble solenoid harness нажмите чтобы увидеть больше wire to screw and torque to 45 in. Torque screw to 45 in. Install briggs and stratton intek repair manual pdf rspair bracket and assemble governor lever to governor shaft, Fig. DO NOT tighten nut at this pdff. Torque control bracket screws to 80 in.
Install intake manifold and carburetor assembly, using new gaskets, Fig. Assemble governor link здесь governor lever. Torque screws to 80 in. Connect solenoid wire to solenoid. Connect breather tube to air horn. Assemble blower housing to engine. Install rotating briggs and stratton intek repair manual pdf.
Assemble air cleaner and install spark plugs. Failure to make the static adjustments first could result in engine overspeeding which may result in engine damage, property damage or personal injury. With governor lever nut loose, rotate governor control swivel counter-clockwise as far as it will go wide open throttle and hold in this position.
Rotate governor shaft clockwise источник far it will go, Fig. Torque governor nut to in. Install throttle and choke control cables and check for proper repaur.
Install fepair manifold. Note: Exhaust manifold and exhaust system supplied by equipment manufacturer. Move equipment control lever to slow position. Hold throttle lever against idle speed adjustment screw and adjust источник speed to RPM, Fig. Release throttle lever. With engine running at governed idle RPM, bend throttle restrictor tang so that tang just contacts governor lever, Fig. The following tools are required when making governor adjustments, Fig.
Tachometer, Tool or Tang bender, Tool or Start and run engine for approximately 5 minutes to allow engine to warm up.
Bend tang to obtain correct RPM, Fig. Open navigation menu.
No comments:
Post a Comment